Chemical Name:	Chemical Family:	CAS Number:
Proprietary	Ink Vehicle	Blend

1. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name:	Amount:	CAS Number:
V-227	100.0%	Blend
(See Section 8 for Exposure Guidelines) • (See Section 15 for Regulatory Information)

2. HAZARDS DISCLOSURE

This product contains no known hazardous materials as defined by the OSHA Hazard Communication Standard 29 CFR 1910.1200. As defined under SARA 311 and 312, this product contains no known hazardous materials.

Back to Top of Page

3. HAZARDS IDENTIFICATION
HMIS Rating:	Health:	1
	Flammability:	1
	Reactivity:	0
	Personal Protection Index:	B
NFPA Rating:	Health:	1
	Flammability:	1
	Reactivity:	0
	Special Hazard:	None

Potential Health Effects:
EYES:	Contact may cause eye irritation.
SKIN:	May cause skin irritation.
INHALATION:	Excessive inhalation may cause headaches, dizziness, drowsiness and nausea.
INGESTION:	No hazards expected in normal industrial use. May cause nausea, vomiting burning sensations, headache, dizziness, incoordination and drowsiness.
CARCINOGENICITY INFO:	No known cancer hazards.

4. FIRST AID MEASURES
EYE CONTACT:	In case of contact, immediately flush eyes with plenty of water for at least 15 minutes. If irritation persists, get medical attention.
SKIN CONTACT:	Immediately wash skin with soap and plenty of water. If irritation persists, get medical attention.
INHALATION:	If exposed to excessive levels of fumes, remove to fresh air. If symptoms persist, get medical attention.
INGESTION:	Contact a physician.

5. FIRE FIGHTING MEASURES
Flammable Properties:
COC FLASHPOINT:	N/A
AUTOIGNITION TEMPERATURE:	N/A
Flammable Limits in Air:
LEL:	N/A
UEL:	N/A
Extinguishing Media:
Use alcohol foam, carbon dioxide or water spray when fighting fires involving this material.
Fire & Explosion Hazards:
During a fire, irritating and toxic gases may be generated by thermal decomposition or combustion.
Fire Fighting Instructions:
As in any fire, wear self-contained breathing apparatus pressure-demand MSHA/NIOSH (approved or equivalent) and full protective gear.

6. ACCIDENTAL RELEASE MEASURES
SAFEGAURDS (Personal):	Wear appropriate personal protective equipment. Eliminate all sources of ignition - heat, sparks, flame, electricity, impact and friction.
INITIAL CONTAINMENT:	Absorb spills with inert material.
LARGE SPILLS PROCEDURE:	Absorb spills with inert material (e g, dry sand or earth), then place in a chemical waste container.
SMALL SPILLS PROCEDURE:	Absorb spills with inert material.

Back to Top of Page

7. HANDLING & STORAGE
HANDLING (Personal):	Do not get in eyes, on skin or clothing. Use only in a well-ventilated area.
HANDLING (Physical Aspects):	Provide appropriate ventilation. Secure container after each use.
STORAGE PRECAUTIONS:	Store in cool dry place.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION
ENGINEERING CONTROLS:	Use only with adequate ventilation.
EYES/FACE PROTECTION REQUIREMENTS:	Where contact with this material is likely, eye protection is recommended.
SKIN PROTECTION REQUIREMENTS:	Wear protective gloves to minimize skin contamination.
RESPIRATORY PROTECTION REQUIREMENTS:	When there is potential for airborne exposures in excess of applicable limits, wear NIOSH/MSHA approved respiratory protection.
EXPOSURE GUIDELINES: Oil Mist, Mineral:	Recommended Exposure Limit: 5 mg/m^3 OSHA PEL: 5 mg/m^3 OSHA TWA: 5 mg/m^3

9. PHYSICAL & CHEMICAL PROPERTIES
FORM:	Liquid
COLOR:	Amber
ODOR:	Characteristic
SOLUBILITY IN WATER:	Nil

Back to Top of Page

10. STABILITY & REACTIVITY
STABILITY:	Stable
POLYMERIZATION:	Hazardous polymerization will not occur.
INCOMPATIBILITY WITH OTHER MATERIALS:	Avoid contact with strong oxidizing agents.
DECOMPOSITION:	May produce fumes, smoke, oxides of carbon and hydrocarbons.

11. TOXICOLOGICAL INFORMATION

No information available.

12. ECOLOGICAL INFORMATION

No information available.

13. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL:	Treat or dispose of waste in accordance with all local state/provincial and national requirements.

14. TRANSPORT INFORMATION
PRODUCT LABEL:	V-227
D.O.T. (Department Of Transportation) SHIPPING NAME:	N/A

15. REGULATORY INFORMATION
MISCELLANEOUS INFORMATION:	The material or all of its components are manufactured in full compliance with the Toxic Substances Control Act (TSCA).

16. OTHER INFORMATION
REASONS FOR ISSUE:	New
PREPARED BY:	Ted Fisk
TITLE:	Technical Director
APPROVAL DATE:	January 1, 2006
SUPERCEDES DATE:	New
ADDITIONAL INFORMATION:	The data in this Material Safety Data Sheet relates only to the specific material designated herein. It does not relate to use in combination with any other material or in any process.
This information is furnished without warranty, expressed or implied, except that it is accurate to the best of our knowledge. The data on this sheet is related only to the specific material designated herein. Bowers Ink Company assumes no legal responsibility for use or reliance upon this date.

Back to Top of Page